Anelace Crystal Blue (2005) User Manual download pdf

FCC Notice

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Radio and Television Interference

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

- - Reorient or relocate the receiving antenna.

- - Increase the separation between the equipment and the receiver.

- - Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- - Consult the dealer or an experienced radio/TV technician for help.

To Contact

AAnneellaaccee,, IInncc..::

On the Web: www.anelace.com

Mail/Warranty Return: Please contact us at

[email protected]

to obtain a return address.

Fig. 4

[A]

[C]

AAnneell aa ccee

- Limited Warranty, US, Canada, EU

This product is warranted by Anelace, Inc. to the original pur-

chaser to be free from defects in material and workmanship

under normal use for a period of 90 days from the date of pur-

chase. During the warranty period, and upon proof of purchase,

the product will be repaired or replaced (with the same or similar

model) at Anelace’s option without any charge for either parts or

labor. This warranty will not apply if the product has been mis-

used, abused, or altered. To obtain warranty service you must

send the product postage paid with a copy of your sales receipt

or other proof of purchase and the date of purchase to address

below. Due to the possibility of damage or loss, it is recom-

mended when sending the product that you package it securely.

NEITHER THIS WARRANTY NOR ANY OTHER WARRANTY,

EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WAR-

RANTY OF MERCHANTABILITY OR OF FITNESS FOR A PAR-

TICULAR PURPOSE, SHALL EXTEND BEYOND THE WAR-

RANTY PERIOD. NO RESPONSIBILITY IS ASSUMED FOR

ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO

YOU.

This warranty gives you specific rights and you may also have

other rights which vary from country to country.

Crystal Blue Powers of 2

™

BCD Clock

AAnneellaaccee IInncc..

English - Español - Français - Deutsch

Product P/N: 950-0006 and EU 950-0006

Powers of 2™ BCD Clock - by

AAnneell aa ccee

This package contains a clock and a power unit.

Reading the clock

This clock is based on the binary number system, the language of computers.

Six digits are required to indicate time. For example, at 10:48 and 36 seconds, we write

10:48:36.

This clock uses 6 columns: each column represents a number value from 0 to 9. The two

columns on the left indicate hours, the middle two are minutes, and the right two are sec-

onds.

The value of each column is determined by which lights are ON:

The bottom light, if ON, is worth “1”. The one above it is worth “ 2,” the third one from the

bottom is worth “4,” and the top one is worth “8.”

Add the values of the ON light positions to get the final value.

• F ig. 1 - In this example, the bottom three lights are ON.

Add their respective values of “1”, “2”, and “4” to get a total value of “7”.

• F ig. 2 illustrates all 10 possible values.

• F ig. 3 demonstrates what the clock will look like at 10:48:36.

Setting up your new “Powers of 2 ™” clock

• F ig. 4: [ A ] Plug the connector at the end of the power unit cord into the socket in the

hole in the bottom of the clock. [ B ] Turn the cord to slip it into the channel, and then [ C ]

rotate the cord to secure it in place.

- Now, plug the power unit into an electrical outlet that matches the adapter that came with

your unit (read the label on the adapter). Anelace sells two versions: a 120V / 60 Hz outlet

model for the normal U.S. power line, and a 220-240V / 50 Hz [EU power line] version for

most other places in the world. A row of lights will scan up and down on the face of the

clock to indicate that the clock has been powered on, but that the time has not yet been set.

This scan will exercise all 20 lights.

⇒⇒

WARNING: Be sure that the line voltage is correct for your adapter.

• Setting the time

- Hours: To set hours, push and release the button marked “H” on the rear of the clock to

advance the hours by one unit. Holding the ‘H’ button down will automatically cycle the

hours forward.

- Minutes: To set minutes, use the above procedure, except push the button marked “M”.

- Seconds: To reset the seconds’ counter to zero, push the “H” and the “M” buttons at

the same time. Release them both to allow the seconds to advance.

• Special options

- 24 hour clock: To activate the 24 hour mode (e.g. 11PM = 23:00:00), hold in the “H”

button when applying AC power to the unit. i.e. when plugging the power unit into the ac

power socket.

- Binary Mode: The clock can be set to operate in “true” binary as opposed to the default

BCD mode. In binary mode, the bottom row of lights represents seconds, the second row

up from the bottom represents minutes and the next row up represents hours (the top row

is not used). See Fig. 5. To enter binary mode, hold in the “M” button when applying

AC power to the unit. i.e. . when plugging the power unit into the ac power socket.

- To activate the true binary display in 24 hour mode, hold both the "H" and "M" buttons

when plugging in the power unit.

- DIM: There are 3 brightness settings for the LED's. Press the "DIM" button found near

where the power cord is plugged into the clock (see FIG. 4) to cycle through the settings.

= Light is “ON”

= Light is “ O F F ”

Fig. 5

Hours

Minutes

Seconds

• The CE Certificate applies to the EU version only

• EU Adaptor: Hon-Kwang # HKA-A0920-230 9V~ 200 mA 1.8 VA.

• The apparatus shall not be exposed to dripping or splashing and no

objects filled with liquids, such as vases, should be placed so that

they can spill on the apparatus.

• Do not cover the apparatus with materials that will impede its

cooling.

[B]

V2-6-04 B.I.S.EU.6.12.04a 14/6/04 9:03 PM Page 1

1 2

Summary of Contents

Page 1 - AAnneellaaccee IInncc

FCC NoticeThis device complies with Part 15 of the FCC rules.Operation is subject to the following two conditions: (1) this device may not cause ha

Page 2 - AAnneell aa ccee

Powers of 2™ BCD Uhr – von AAnneell aa cceeDas Paket enthält eine Uhr und ein Netzteil zur Stromversorgung.Ablesen der UhrzeitDie Uhr basiert auf dem

Comments to this Manuals

No comments

Anelace Crystal Blue (2005) User Manual

Browse online or download User Manual for Clock Anelace Crystal Blue (2005). Anelace Crystal Blue (2005) User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Clock Anelace Crystal Blue (2005)